- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
I've tried a couple different POE injectors and adapters but none will charge the battery for the camera. So far they all end up with a message on the camera saying "The charging source connected to the camera cannot charge your battery...." Has anyone found a product that will charge the battery yet?
My Setup: Linksys MX10 on Frontier FIOS 500/500.
Also experienced with AT&T Fiber & Charter Cable
Solved! Go to Solution.
- Related Labels:
-
Installation
-
Troubleshooting
Accepted Solutions
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
OK, So I found a solution to this problem and it is charging the camera over ethernet.
You will need one pair of these SinLoon(2-PACK) AF-RJ45 USB to USB Female to AF-8P8C Connector Crystal USB, USB Transfer Network Plu... These simply convert the power to allow it to go over ethernet with whatever charger you want to use and don't require a POE switch.
I then purchased a USB-A male-to-male cable and connected the Arlo charger to one end and the other end to one adapter. The other adapter connects to the Arlo USB cable and the camera at the other end of the ethernet run.
YMMV depending on the length of the ethernet run. In my case, the run is at least 50 feet to a storage closet that didn't have any electrical outlets.
My Setup: Linksys MX10 on Frontier FIOS 500/500.
Also experienced with AT&T Fiber & Charter Cable
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Not really true....
The Pro and Pro2 use a Qualcomm type dual voltage charger. The adapter will put out 5v( stanard usb output) via the usb or 9v depending on what it is plugged into. You can NOT charge an 8.4v cell pack ( listed as 7.2v but charges to 8.4 ) with the 5v only and that is why it also puts out 9v.
If used in any other devices, the adapter should work as normal.... Also SOME qualcomm type charges will work with the cameras but not all ( voltage level is specific ).. I have tested my S7 phone dual voltage adapter and it worked fine for me on a Pro2. YMMV.
Morse is faster than texting!
--------------------------------------
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
OK, So I found a solution to this problem and it is charging the camera over ethernet.
You will need one pair of these SinLoon(2-PACK) AF-RJ45 USB to USB Female to AF-8P8C Connector Crystal USB, USB Transfer Network Plu... These simply convert the power to allow it to go over ethernet with whatever charger you want to use and don't require a POE switch.
I then purchased a USB-A male-to-male cable and connected the Arlo charger to one end and the other end to one adapter. The other adapter connects to the Arlo USB cable and the camera at the other end of the ethernet run.
YMMV depending on the length of the ethernet run. In my case, the run is at least 50 feet to a storage closet that didn't have any electrical outlets.
My Setup: Linksys MX10 on Frontier FIOS 500/500.
Also experienced with AT&T Fiber & Charter Cable
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
I'm looking at a POE solution for the Pro 2. Can you provide a link for the other items used? Also, not clear to me how you are interconnecting all these items to power the camera?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
@Greatg269 wrote:
I'm looking at a POE solution for the Pro 2. Can you provide a link for the other items used? Also, not clear to me how you are interconnecting all these items to power the camera?
It worked for a few days but the camera has since started showing the incompatible charger notice again.
My Setup: Linksys MX10 on Frontier FIOS 500/500.
Also experienced with AT&T Fiber & Charter Cable
-
Apple HomeKit
1 -
Arlo Mobile App
369 -
Arlo Pro
27 -
Arlo Pro 2
1 -
Arlo Pro 3
2 -
Arlo Secure
1 -
Arlo Smart
87 -
Arlo Ultra
1 -
Arlo Web and Mobile Apps
6 -
Arlo Wire-Free
10 -
Before You Buy
1,186 -
Discovery
1 -
Features
205 -
Firmware
1 -
Firmware Release Notes
119 -
Hardware
2 -
IFTTT
1 -
IFTTT (If This Then That)
48 -
Installation
1,402 -
Installation & Upgrade
1 -
Online and Mobile Apps
1,266 -
Partner Integrations
1 -
Security
1 -
Service and Storage
563 -
Smart Subscription
1 -
SmartThings
39 -
Software & Apps
1 -
Troubleshooting
7,192 -
Videos
1
- « Previous
- Next »