Arlo|Smart Home Security|Wireless HD Security Cameras|NETGEAR
Reply
Highlighted
Initiate

Base Station Is Offline

Can anyone help please? My system was working fine until a couple of days ago, my app now shows the base station is offline. I have turned the base station off and on, reset it, removed cables but with no joy. The base station power light is permanent green The internet light is solid but then flashes 4 times all green The camera light is permanently amber. Any ideas?

Model: VMB4500 | Arlo Pro/Pro2 Base Station
Message 1 of 18

Accepted Solutions
Guru

Base Station Is Offline

Use the Add Device selection on the Devices tab to claim the base again. The solid amber Camera LED means the base needs to be claimed. Worst case, you may need to remove all devices from Settings, My Devices and start fresh.

Message 2 of 18

All Replies
Guru

Base Station Is Offline

Use the Add Device selection on the Devices tab to claim the base again. The solid amber Camera LED means the base needs to be claimed. Worst case, you may need to remove all devices from Settings, My Devices and start fresh.

Message 2 of 18
Initiate

Base Station Is Offline

Thank you that worked, much appreciated.

Model: VMB4000 | Arlo Pro/Pro2 Base Station
Message 3 of 18
Aspirant

Re: Base Station Is Offline

My base station was offline this morning. After reading some of the solutions, I pressed the Sync button on the base station. Only one camera came back online. The other two did not.  What do I do now?

Message 4 of 18
Arlo Moderator

Re: Base Station Is Offline

@Toni1946

 

Have you tried to remove the batteries for the Pro/Pro2 & or open and close the battery door for the (Origina Wire Free)?

Message 5 of 18
Aspirant

Re: Base Station Is Offline

I have not tried that yet.  I will tonight as soon as I get home.  Thank you so much. I sure hope it works. I don't want to have to call someone out!

Message 6 of 18
Aspirant

Re: Base Station Is Offline

My base station worked fine up untill two days ago and then it said it was offline . ive tried resetting it and removing it from my appthen tryiny to add it back but my app dosent even detect it . it says no device found. the base station has all three lights green on it but its not send out any signal

Model: VMB4000 | Arlo Pro/Pro2 Base Station
Message 7 of 18
Guru

Re: Base Station Is Offline

Since you've already started the reset process, finish it. Remove all devices in Settings, My Devices. Hold the base reset button until the LEDs flash amber. Once it's rebooted, use the Add Device selection on the Devices tab to claim the base. Sync the ecameras. Update firmware as you go, if prompted.

 

Having all 3 green LEDs means the base is stil recognized so it can't be claimed again. The above will resolve that issue.

Message 8 of 18
Aspirant

Re: Base Station Is Offline

Thank you for all the suggestions. I did have to change the batteries (not sure I had to put fresh batteries in the cameras, but did that anyway). They did finally sync with the base station, after I had hit the sync button on the base station.

Message 9 of 18
Aspirant

Re: Base Station Is Offline

I just set up my security system for the first time. When I try to synch the cameras, the amber light comes on. I would guess that my base station has not been "claimed" or registered or what ever so the cameras can't synch to the base. How do I claim or register the base so I can synch the cameras?


@Alan_1 wrote:

Can anyone help please? My system was working fine until a couple of days ago, my app now shows the base station is offline. I have turned the base station off and on, reset it, removed cables but with no joy. The base station power light is permanent green The internet light is solid but then flashes 4 times all green The camera light is permanently amber. Any ideas?


 

Message 10 of 18
Aspirant

Re: Base Station Is Offline

When mine went offline, I held the button top of the station for a few seconds to sync it to my wifi. It worked.

Message 11 of 18
Aspirant

Re: Base Station Is Offline

I had to switch out the batteties on my two other cameras, even though they were still good, and that did the trick!

Message 12 of 18
Guru

Re: Base Station Is Offline


@tjbrn wrote:

I just set up my security system for the first time. When I try to synch the cameras, the amber light comes on. I would guess that my base station has not been "claimed" or registered or what ever so the cameras can't synch to the base. How do I claim or register the base so I can synch the cameras?


Use the directions that came with the system. The Add Device selection on the Devices tab is used to claim the base. Just choose the picture with all the different bases and follow the directions.

Message 13 of 18
Aspirant

Re: Base Station Is Offline

I have 4 cameras up and I am getting a message that it’s offline! I have removed them from the base station twice and added them back. How many times do I have to do this?
Model: VMB4000 | Arlo Pro/Pro2 Base Station
Message 14 of 18
Aspirant

Re: Base Station Is Offline

My Arlo base just two days ago went offline and all the cameras are not detectable. Any reason why and how do I recover?? 

Model: VMB3000 | Arlo Base Station
Message 15 of 18
Guru

Re: Base Station Is Offline

What are the LEDs on the base showing? Have you turned the base off and back on? Have you logged out and back in? What have you tried? What do you see?

Message 16 of 18
Aspirant

Re: Base Station Is Offline

I have removed them and reset them up. Some times the internet flashed yellow on the home base but then turns back to green. It seems to be okay now. I have learned though that birds fly at night much to my surprise.
Message 17 of 18
Aspirant

Re: Base Station Is Offline

same situation here, have tried removing all devices, removed batteries on 3 cameras, reconnected base station, tried to sync 3 cameras ..... still comes back with devices offline ..... why has this suddnely happened, and how many times do I have to try to reset everything up??

Model: VMB3000 | Arlo Base Station
Message 18 of 18