- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Purchased an Essential Outdoor 2nd Gen camera. The camera keeps going offline. Checked WiFi connectivity, signal strength, etc all checks out fine. Network strength shows strong, however the camera goes offline randomly. It eventually comes back online, sometimes within minutes, sometimes hours or days later. Need some guidance on what could be causing the problem.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
It could be 2.4GHz interference. Try moving the camera to a different location to see if that fixes the issue.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Moved camera, no difference. Here’s what I’ve observed so far.
Camera seems to go offline mostly at night.
Once motion is detected in that area, within minutes camera comes back online and stays on until the following night.
Other devices ( including cameras) aren’t dropping off.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
How close are you to the nearest neighbor's house? Just wondering if their WiFi is interfering with the signal. You can use a WiFi app on your phone to check during the day and then at night to see if there's a difference while standing next to the camera.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
An update to this issue. After over a month going back and forth with support, this issue was not resolved. All of a sudden it stopped going offline, then after almost a month it started all over again. Last update from support was to move camera near router, check wifi connectivity, make sure you are on 2.4 ghz network, check upload speed on internet, ask isp for increase of upload speed, etc. Nothing worked. Frustrated at lack of personal support given, it's like they are reading off of the support articles already written from Arlo, of which I have already read. I have computer knowledge as well as network knowledge, but I can't imagine someone without some network knowledge trying to get these gen 2 cameras to work. Anyway, it's going offline again, we walk out create motion, and it comes back online. If anyone has had this issue and has solved it, I would love to hear from them.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
I have reached out to support so they can look into this further with you. They will be reaching out as soon as possible.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
I have a same issue the camera goes offline and can't connect, no response and motion detected logo appear on apps but keep connecting then frozen. Checked WIFI under 2.4Ghz, no issue found on other cameras when its connect to my base station.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Sorry you are having same issue but glad it’s not just me. Hopefully this can get resolved.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
I have the same issue. It worked well for a while then started to disconnect and uninstalled cameras from app. Had to reinstall cameras on app but disconnected and uninstalled by itself again and again.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
When we first got the camera it was going offline constantly. Support said it needed a firmware update. Took camera down and updated camera. Condition still persisted. Support had me check signal strength, it was always strong. Camera stopped going offline for about two weeks then started all over again. Now it goes offline and online at various times thru the day. When it goes offline, if you walk in front of it, in about five minutes time it does came back online.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
I’m having the same issue. Camera about 18 feet away from neighbors house in a narrow side yard, dark too.
It seems to be about the location. I swapped the camera with another identical camera that had been working fine.
Within hours, the new camera in the problem spot was going offline, and the other location was just fine.
i haven’t contacted support bc i knew it would be useless, as the original poster experienced.
I’ll try moving the camera next, which is too bad, the original spot was perfect.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
@ Pam
I too have professional experience.
I recently got a 4 pack and 3/4 will not maintain their boot sequence to the updated Firmware.
I ended up after 96 hours of wasted effort logged a ticket and had the issue of out of date Firmware raised to 2nd level support. The Level 1 help desk response was 'known issue, re-mediation is under way' try hard reset ( 25 seconds on the button) and re add to the App.
Check your Firmware levels against the latest set. I've learnt that my old set of Arlos whilst simple are probably currently better than the new range. I'm mildly unhappy but at least hte New Solar panels are not the same $ as last time and have seals on the ports.
Engineers are working on it .... which means that ... they are overloaded or don't have the best toolchain.
https://community.arlo.com/t5/Firmware-Release-Notes/Arlo-Firmware-Release-Table/m-p/1920885
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
@prunesquallor wrote:
It seems to be about the location. I swapped the camera with another identical camera that had been working fine.
Try testing your internet speed at the camera location using your phone.
Use the free Ookla (speedtest) app. Turn off mobile data during the test, to make sure you are testing your home wifi speed.
Upload speed is more important than download for the cameras. The app will also report packet loss, which also could be a factor at the location.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Double Check your Firmware is up to latest
WiFi Channel overlap is very common on 2.4 spectrum, which is why the standards evolved. unfortunately your cameras may be in range of many WiFi Access points /range extenders and routers offering connection automatically. Unfortunately they may be hearing many more signals than just your own router.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Can you please provide app version as well as what type of device you are using?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
App 5.0.2
Essentials outdoor gen 2 VMC 3050
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
I have reached out to our development team to investigate the behavior you are seeing. I will update the community as soon as possible.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Thanks so much!!
-
180 degree
1 -
250-50602-01
1 -
Android App
1 -
animal
1 -
api_key
1 -
Arlo
1 -
Arlo 2nd Gen
1 -
Arlo Cameras
2 -
Arlo Essential 2nd Gen always goes offline
1 -
Arlo Essential Spotlight
2 -
Arlo Mobile App
1 -
Arlo Secure 4.0
1 -
Arlo Smart
1 -
base station
1 -
Batteries
1 -
Battery life
2 -
Battery.
1 -
camera
2 -
connection
1 -
constant
1 -
customer service
1 -
drained battery
1 -
Essential
1 -
Essential Camera feature request
1 -
Essential outdoor
1 -
Features
2 -
freeze
1 -
Google Nest
1 -
Idk
1 -
motion
1 -
Motion Detection
3 -
motiondetection
1 -
need help
1 -
network
1 -
New features
1 -
Night vision
1 -
No recordings
1 -
not working
1 -
Orbi
1 -
Other Discussions
1 -
Payment
1 -
privacy zones essential 2k
1 -
problemshooting
1 -
Product
1 -
Record
1 -
Reliable
1 -
returns
1 -
Router
1 -
sensor not working
1 -
Siren
1 -
smart things
1 -
Troubleshooting
5 -
Unknown charges
1 -
VMC3050
1
- « Previous
- Next »