- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
The base station is offline even if connected to the internet
Solved! Go to Solution.
- Related Labels:
-
Installation
-
Troubleshooting
Accepted Solutions
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
AN amber Camera LED means the base needs to be claimed. Nothing will work until that happens. Remove all devices found in Settings, My Devices and start fresh. Use the Add Device button on the Devices tab to claim your base. Sync your cameras. Update firmware if prompted as you go.
You said you've "reset" but that means different things to different people. Many think a power cycle/reboot is a reset but it isn't. A reset comes when you perform the steps above or you push the reset button on the base until the LEDs flash amber. If that's what you did, that would explain your problem and the above procedure will get you going again. A true reset means you have to follow that process.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Need a lot more detail. What are the base LEDs showing? What have you tried? What do you see, including error messages?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Thanks for your reply
Please note the base leds are showing green green (flickering ) and yellow
Have tried resetting to no avail
Brgds
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Thanks for your reply
Please note the base leds are showing green green (flickering ) and yellow
Have tried resetting But the base is still offline and the cameras are not recording
Brgds
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
AN amber Camera LED means the base needs to be claimed. Nothing will work until that happens. Remove all devices found in Settings, My Devices and start fresh. Use the Add Device button on the Devices tab to claim your base. Sync your cameras. Update firmware if prompted as you go.
You said you've "reset" but that means different things to different people. Many think a power cycle/reboot is a reset but it isn't. A reset comes when you perform the steps above or you push the reset button on the base until the LEDs flash amber. If that's what you did, that would explain your problem and the above procedure will get you going again. A true reset means you have to follow that process.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Dear Guru
the problem have Ben solved.
Thanks a lot for the help
brgds
-
Apple HomeKit
1 -
Arlo Mobile App
370 -
Arlo Pro
27 -
Arlo Pro 2
1 -
Arlo Pro 3
2 -
Arlo Secure
1 -
Arlo Smart
87 -
Arlo Ultra
1 -
Arlo Web and Mobile Apps
6 -
Arlo Wire-Free
10 -
Before You Buy
1,187 -
Discovery
1 -
Features
205 -
Firmware
1 -
Firmware Release Notes
119 -
Hardware
2 -
IFTTT
1 -
IFTTT (If This Then That)
48 -
Installation
1,402 -
Installation & Upgrade
1 -
Online and Mobile Apps
1,266 -
Partner Integrations
1 -
Security
1 -
Service and Storage
563 -
Smart Subscription
1 -
SmartThings
39 -
Software & Apps
1 -
Troubleshooting
7,192 -
Videos
1
- « Previous
- Next »