Dannybear, maybe this is what Arlo/Netgear is hoping for as they sure as hell aren't doing much to fix this problem, and if they are, they need to dramatically improve their communication skills. A little communication goes a long way, yet they do not even mention wide spread issues on their website. Why????????????????????????????????????????????????????????
If I was a betting person, I would put my money on this issue is a result of intended behaviour to repair faulty base station.
I suspect the reason arlo is not forthcoming and meting out only specific detail is that the bean counters and lawyers are at the reigns.
Appreciate you defending my factual post with your own factual posts. Unfortunately there are others on this forum who can't believe not all of us continue to be plaugued with the same problems as them. This suggests the problem is no longer systemwide. Like any other forum we unfortunately get ***** * punks who insist they are always right.
Not sure what da heck is going on, but 2 of my cameras (both Pro and Pro 2) got stuck in Firmware update mode.
It's dead now and will be replaced by Arlo and Costco.
No, If you read as far back as 2015 on this forum you will see that Arlo has always behaved this way.
The comb 4000 base issues have been around since October last year just before I purchased my system.
If only I had a crystal ball.
I took an hour tonight and created my own support ticket for the Base Station rebooting issue we've all been seeing.
In the outcome of my ticket, I was given my own support ticket number, and told "our engineering think this is a problem with the firmware of the base station." and, "They are still working on creating a new firmware and once the firmware is up your base station will just automatically update it."
Additionally, I should receive an email alert when they are pushing the firmware update out to address this issue and was told my ticket will not close before I confirm my issues have been addressed.
Instead of getting super upset in these forums, my best advice is for each of you to take the time to open a new ticket with Arlo's support chat system and answer their very simple questions one at a time, so they have more visibility of this issue. The more users report this, the higher their engineering department will take Urgency of this problem.
Here's hoping this gets resolved soon!
In addition, we had a package stolen from out front doorstep a few weeks ago but thankfully the base station was working at that time. A few hours ago we’ve had another package left on out front doorstep (despite requests not to) and if it too is stolen, and if the base station (which is again offline as I type this) isn’t online if that package is stolen I’m going to be mightily pissed off!
There are also phone numbers to call on the support page. I don't know why chat can be problematic but some have suggested leaving the (blank) page open and that it may work after some time.
Yeah, thanks Arlo engineering. ****-poor testing.
"Required Base Station firmware upgrade." Fine, have at-it.
45 minutes later; "Base Station Offline".
This is my Florida Residence. I do not plan to return for MONTHS to reset the thing.
Arlo Engineering: Either test your c*** or do NOT REQUIRE a Firmware Upgrade. Absolute **** poor engineering practice. You lost sight of your objective: You're a security appliance. You do not "force" a FW upgrade from your user-base; without full disclosure and proper testing.
..From an Electrical Engineer.
Has there been a resolve to this yet?
Mine keep doing an endless cycle of firmware update needed, base station offline, base station up and records in wrong timezone, back to firmware update needed.
I contacted the 'brains' of the customer support line and I was given the same scripted instructions they give everyone.
I was told by them there is no known problem, to which I directed them to this message board.
That happened to a camera of mine once.
Another Camera didnt go into night vision.
Now..Its my base station that is stuck. I was actually starting to assume that they were implementing a forced upgrade by making the hardware obsolete for the mandatory firmware update....?
Time zone looks fixed but the base station going offline is inly getting worse . Its now going in 8 hours and no matter how many times i reset or restart i get nothing! Right now i have a pile of useless junk and if Arlos technical team moves as fast as they did on the time zone issue we are all